求IEC-60034-1(ISIRI 3772)检验报道如何填写？

Glendon

DESCRIPTION		STANDARD LIMIT	RESULTS				REMARKS PASS/FALL
RERED OUTPUT(W)		AS PER SUB CLAUSE 4.5.3.THIS IS THE MACHANICAL POWER AVAILABLE AT THE SHAFT AND SHALL BE EXPRESSED IN WATTS	2	2	2	2	Pass
EFFICIENCY(%)							Pass
POWER FACTOR		≤6W	6.0	6.1	6.0	6．2	Pass
INPUT POWER	NO-LOAD	≤6W	6.0	6.0	6.0	6.0	pass
	FULL-LOAD	≤6W	6.0	6.0	6.0	6.0	pass
CURRENT	NO-LOAD	≤29	29	29	29	29	pass
	FULL-LOAD	≤29	29	29	29	29	pass
TORQUE		≤1.8w/m	1.8	1.9	1.8	1.8	Pass
LOCKED-ROTOR TORQUE		≤2.0	2.0	2.0	2.0	2.0	Pass
DUTY TYPE		AS PER SUB CLAUSE3.2, SPECIFY ONE OF THE TYPES FROM SI TO S10					Pass
THERMAL CLASSIFICATION		IEC60085					Pass
REFERENCE COOLANT		AS SPECIFIED IN TABLE3					Pass
SITE OPERATION CONDITIONS UNLESS OTHERWISE SPECIFIED MACHINES SHALL BE SUITABLE FOR THE FOLLOWING SITE OPERATION CONDITIONS		ALTTUDE SHALL NOT EXCEED 1000M ABOVE SEA LEVEL					Pass
	MAXIMUM AMBIENT AIR TEMPERATURE SHALL NOT EXCEED 40℃。					Pass
	MINIMUN AMBIENT AIR TEMPERATURE SHALL NOT BE LESS THAN -15℃。 FOR ANY MACHINE ALSO AS PER SUB CLAUSE 5.4					Pass
	WATERCOOLAN TEMPERATURE AT THE INLET TO A MACHINE OR HEAT EXCHANGER SHALL NOT EXCEED +25℃ NOR LESS THAN +5℃					Pass
CONDITIONS THERMAL TESTS		AS SPECIFIED IN SUB CLAUSE 7.3					Pass
TEMP RISE OF A PART OF A MACHINE		AS SPECIFIED IN SUB CLAUSE 7.4					Pass
ELECTRICAL SUPPLY		AS SPECIFIED IN SUB CLAUSE 6.1					Pass
FORM AND SYMMETRY OF VOLTAGE CURRENTS		AS SPECIFIED IN SUB CLAUSE 6.2 AND TABLE 1					Pass
VOLTAGE AND FREQUENCY VARIATIONS DURING OPERATION		IN ACCORDANCD WITH FIGUER 12 AND AS SPECIFIED IN SUB 6.3	220V 50HZ				Pass
VOLTAGE (PEAK AND GRADIENT) WITHSTAND LEVELS		FOR A.C MOTORS THE MANUFACTURE SHALL DECLARE A LIMITING VALUE FOR THE PEAK VOLTAGE AND FOR THE VOLTAGE GRADUEBT INCONTINUOUS OPERATION	220V -240V				Pass
DIELECTRIC TEST		AS PER SUB CLAUSE 8.1 AND TABLE 14	CLASS H				Pass

Glendon

19	OCCASIONAL EXCESS CURRENT	AS PER SUB CLAUSE8.2.3					Pass
20	PULL-UP TORQUE	SHALL COMPLY WITH REQUIREMENTS OF SUB CLAUSE 8.4	1.8N/M				Pass
21	OVER SPEED	AS PER SUB CLAUSE 8.5 AND SHALL WITHSTAND THE SPEEDS SPECIFIED IN TABLE15	2.0				Pass
22	SHORT CIRCUIT WITHSTAND TEST	AS PER SUB CLAUSE 8.7					Pass
23	NO.OF POLES		2.0				Pass
24	SPEED OF MOTOR AT FULL LOAD						pass
25	SLIPPAGE	SLIPPAGE IS COMPUTED AS BELOW S=[N/60 X NUMBER OF POLES]-1 _____ _________________ F 2 WHERE N IS RPM AT FULL LOAD F=FREQUENCY OF MAIN IN HZ (50HZ UB IRAN)					Pass
26	MARKING	AS PER SUB CLAUSE 9.2	49TYD CLH 6W 220V-240V CE				Pass
27	EARTHING OF MACHINE	AS PER SUB CLAUSE 10.1					Pass
28	SAFETY	ACCORDING TO IEC 60201-1					pass
29	TOLERANCES	SHALL BE AS SPECIFIED IN TABLE 18					Pass
30	SHAKE OF MOTOR						Pass