| DESCRIPTION | STANDARD LIMIT | RESULTS | REMARKS PASS/FALL | ||||
| RERED OUTPUT(W) | AS PER SUB CLAUSE 4.5.3.THIS IS THE MACHANICAL POWER AVAILABLE AT THE SHAFT AND SHALL BE EXPRESSED IN WATTS | 2 | 2 | 2 | 2 | Pass | |
| EFFICIENCY(%) | | Pass | |||||
| POWER FACTOR | ≤6W | 6.0 | 6.1 | 6.0 | 6．2 | Pass | |
| INPUT POWER | NO-LOAD | ≤6W | 6.0 | 6.0 | 6.0 | 6.0 | pass |
| FULL-LOAD | ≤6W | 6.0 | 6.0 | 6.0 | 6.0 | pass | |
| CURRENT | NO-LOAD | ≤29 | 29 | 29 | 29 | 29 | pass |
| FULL-LOAD | ≤29 | 29 | 29 | 29 | 29 | pass | |
TORQUE | ≤1.8w/m | 1.8 | 1.9 | 1.8 | 1.8 | Pass | |
| LOCKED-ROTOR TORQUE | ≤2.0 | 2.0 | 2.0 | 2.0 | 2.0 | Pass | |
| DUTY TYPE | AS PER SUB CLAUSE3.2, SPECIFY ONE OF THE TYPES FROM SI TO S10 | | Pass | ||||
| THERMAL CLASSIFICATION | IEC60085 | | Pass | ||||
| REFERENCE COOLANT | AS SPECIFIED IN TABLE3 | | Pass | ||||
| SITE OPERATION CONDITIONS UNLESS OTHERWISE SPECIFIED MACHINES SHALL BE SUITABLE FOR THE FOLLOWING SITE OPERATION CONDITIONS | ALTTUDE SHALL NOT EXCEED 1000M ABOVE SEA LEVEL | Pass | |||||
| MAXIMUM AMBIENT AIR TEMPERATURE SHALL NOT EXCEED 40℃。 | Pass | ||||||
| MINIMUN AMBIENT AIR TEMPERATURE SHALL NOT BE LESS THAN -15℃。 FOR ANY MACHINE ALSO AS PER SUB CLAUSE 5.4 | Pass | ||||||
| WATERCOOLAN TEMPERATURE AT THE INLET TO A MACHINE OR HEAT EXCHANGER SHALL NOT EXCEED +25℃ NOR LESS THAN +5℃ | | Pass | |||||
| CONDITIONS THERMAL TESTS | AS SPECIFIED IN SUB CLAUSE 7.3 | | Pass | ||||
| TEMP RISE OF A PART OF A MACHINE | AS SPECIFIED IN SUB CLAUSE 7.4 | | Pass | ||||
| ELECTRICAL SUPPLY | AS SPECIFIED IN SUB CLAUSE 6.1 | | Pass | ||||
| FORM AND SYMMETRY OF VOLTAGE CURRENTS | AS SPECIFIED IN SUB CLAUSE 6.2 AND TABLE 1 | | Pass | ||||
| VOLTAGE AND FREQUENCY VARIATIONS DURING OPERATION | IN ACCORDANCD WITH FIGUER 12 AND AS SPECIFIED IN SUB 6.3 | 220V 50HZ | Pass | ||||
| VOLTAGE (PEAK AND GRADIENT) WITHSTAND LEVELS | FOR A.C MOTORS THE MANUFACTURE SHALL DECLARE A LIMITING VALUE FOR THE PEAK VOLTAGE AND FOR THE VOLTAGE GRADUEBT INCONTINUOUS OPERATION | 220V -240V | Pass | ||||
| DIELECTRIC TEST | AS PER SUB CLAUSE 8.1 AND TABLE 14 | CLASS H | Pass |
19 | OCCASIONAL EXCESS CURRENT | AS PER SUB CLAUSE8.2.3 | | Pass | |||
20 | PULL-UP TORQUE | SHALL COMPLY WITH REQUIREMENTS OF SUB CLAUSE 8.4 | 1.8N/M | Pass | |||
21 | OVER SPEED | AS PER SUB CLAUSE 8.5 AND SHALL WITHSTAND THE SPEEDS SPECIFIED IN TABLE15 | 2.0 | Pass | |||
22 | SHORT CIRCUIT WITHSTAND TEST | AS PER SUB CLAUSE 8.7 | | Pass | |||
23 | NO.OF POLES | 2.0 | Pass | ||||
24 | SPEED OF MOTOR AT FULL LOAD | pass | |||||
25 | SLIPPAGE | SLIPPAGE IS COMPUTED AS BELOW S=[N/60 X NUMBER OF POLES]-1 _____ _________________ F 2 WHERE N IS RPM AT FULL LOAD F=FREQUENCY OF MAIN IN HZ (50HZ UB IRAN) | Pass | ||||
26 | MARKING | AS PER SUB CLAUSE 9.2 | 49TYD CLH 6W 220V-240V CE | Pass | |||
27 | EARTHING OF MACHINE | AS PER SUB CLAUSE 10.1 | Pass | ||||
28 | SAFETY | ACCORDING TO IEC 60201-1 | pass | ||||
29 | TOLERANCES | SHALL BE AS SPECIFIED IN TABLE 18 | Pass | ||||
30 | SHAKE OF MOTOR | Pass |
| 欢迎光临 标准下载论坛 (http://bbs.bzxzk.net/) | Powered by Discuz! X3.2 |